In stock

Module 83 - VAG Bosch DQ380, DQ381, DQ500, ZF 8HP

$188.98

Manufacturer

PCMflash

Description

Reviews (0)

Caption:

RD: Read
WR: Write
CK: Checksum correction

Supported ECU

DQ380/381/500 (0DE/0DL/0GC) [VR/WR/CK]
AL420/AL600 (09L/09E) K-Line [VR/RD/WR/CK]
AL420/AL600 (09L/09E) CAN TP2.0 [VR/RD/WR/CK]
AL450/AL551/AL951 (0CM/0BK/0BL) [VR/RD/WR/CK]
AL552/AL952 (0D5/0D6) [VR/WR/CK]
AL1000/AQ250/AQ450 (0C8/09G) UDS [VR/WR/CK]
AL600/AL750/AQ250 (09D/09G) K-Line [Test] [RD/WR/CK]
AL750/AQ250 (09D/09G) CAN TP2.0 [Test] [RD/WR/CK]

In version 1.2.5, a new module 83 “VAG Bosch DQ380/DQ381/DQ500/ZF 8HP” has been added, designed to work through the vehicle’s diagnostic port with DSG and automatic transmission ECUs used in VAG group vehicles. It supports virtual reading, writing, checksum verification, and correction. This module is intended exclusively for tuning or updating the transmission control software. For cloning and working with EEPROM, use module 82.

DQ380/381/500 (0DE/0DL/0GC) [VR/WR/CK]
AL450/AL551/AL951 (0CM/0BK/0BL) [VR/RD/WR/CK]
AL552/AL952 (0D5/0D6) [VR/WR/CK]

“Real” reading is currently only supported for AL551, while for AL450/AL951, it’s still under review. Reading is limited to the calibration (maps) area, whereas virtual reading covers the entire software. Therefore, files from virtual reading can be used to change the software version, but files from regular reading cannot.

WARNING: DQ380/381/500 has a peculiarity in file naming. The manufacturer decided to use the same part number for mechatronics across different configurations, so the list of files provided by the program may contain INCOMPATIBLE files, for example, different shift points for diesel and gasoline engines. To determine file compatibility when changing the software version, it is MANDATORY to ensure that the last 4 characters in the file name match those seen in the ECU identification.

Example of DQ381 identification:

Part number: 0GC300012B

Software version: 1643

Component: GSG DQ381

Hardware number: 0GC927711H

ASAM: EV_TCMDQ381061

Parameter: FL_0GC300012B_1643_VPWZ.par

VIN number:

Coding: 0007

Programming count: 2

ECU type: DQ381/DQ500 Bosch

Look at the “Parameter” in the identification result. The last 4 characters are VPWZ. Select from the list only those options for 0GC300012B that contain VPWZ:

0GC300012B_1404_VPWZ
0GC300012B_1405_OPWZ
0GC300012B_1406_OTWZ
0GC300012B_1420_VPWZ
0GC300012B_1421_OPWZ
0GC300012B_1422_OTWZ
0GC300012B_1426_VPWZ
0GC300012B_1427_OPWZ
0GC300012B_1428_OTWZ
0GC300012B_1429_RTWZ
0GC300012B_1434_OPWZ
0GC300012B_1638_OPWZ
0GC300012B_1640_OTWZ
0GC300012B_1641_RTWZ
0GC300012B_1642_OPWZ
0GC300012B_1643_VPWZ
0GC300012B_1644_OTWZ

DQ381 writing log:

13:43:44 Entering programming mode
13:43:45 Gaining access
13:43:46 Transferring data
13:43:46 Erase area 1
13:43:48 Transferring block 1
13:44:00 Verifying
13:44:00 Erase area 2
13:44:08 Transferring block 2
13:45:54 Verifying
13:45:55 Erase area 3
13:45:56 Transferring block 3
13:46:04 Verifying
13:46:05 Software validation
13:46:05 Completing
13:46:08 Completed successfully

AL551 calibration reading log:

14:11:43 Identifying module
14:11:43 Software version: AL551_8R1927158H_1005
14:11:43 Reading data
14:11:43 Reading block 1
14:15:00 Completed successfully

AL551 calibration writing log:

14:19:27 Preparation
14:19:33 Entering programming mode
14:19:34 Gaining access
14:19:35 Transferring data
14:19:35 Erase area 1
14:19:38 Transferring block 1
14:19:50 Verification
14:19:51 Software validation
14:19:51 Finish

AL552 full writing log:

12:35:54 Preparing
12:35:59 Entering programming mode
12:36:01 Gaining access
12:36:01 Transferring data
12:36:01 Erase area 1
12:36:10 Transferring block 1
12:37:25 Verifying
12:37:46 Erase area 2
12:37:49 Transferring block 2
12:38:02 Verifying
12:38:08 Validating software
12:38:08 Finishing