In stock

Module 38 - Renault K Line

$94.49

Manufacturer

PCMflash

Manufacturer

PCM Flash

Basic equipment

Module 38

Description

Reviews (0)

Caption:

RD: Read
WR: Write
CK: Checksum correction

Supported ECU

Duster 1.6L 2WD EMS3130 (ST10/512KB) [ RD/WR/CK ]
EMS3132 MT (C167/256KB) [ RD/WR/CK ]
EMS3134 AT (C167/512KB) [ RD/WR/CK ]
Sagem 3000 (SH7055/512KB) [ RD/WR/CK ]
Sirius 35 (C167/512KB) [ RD/WR/CK ]

These ECUs are found in various vehicles, including the Renault Duster (1.6L, front-wheel drive – EMS3130), Renault Logan 1, Sandero 1, Lada Largus, and Nissan Almera with manual transmissions (EMS3132). The EMS3134 is used in similar models with automatic transmissions. These ECUs can also be found in many other Renault vehicles with engines ranging from 1.4 to 2.0 liters.

The modules support both calibration reading/writing and full ECU software writing. Before starting any operations, ensure you select or confirm the appropriate operating mode. These modules also support various file formats from different loaders.

Important: When writing full ECU software, ensure it matches the vehicle! The VIN number is embedded in the ECU firmware, and if necessary, this information must be transferred. However, this step is not required when working only with calibrations. To help, fully read files will include the vehicle’s VIN in the filename.

EMS3130 – Working with calibrations:

“ VIN: X7LHSRH854941

Calibration ID: 3515R

Main Number: 0826R

Hardware Number: 0828R

09:49:33 – Module identification

09:49:34 – Software version: SW3515R_HW0828R

09:49:34 – Access granted

09:49:34 – Reading data

09:50:14 – Successfully completed

10:00:07 Module identification
10:00:09 Access granted
10:00:10 Erasing
10:00:11 Transferring data
10:00:11 Transferring block 1
10:00:30 Software validation
10:00:38 Completion
10:00:39 Successfully completed

File Naming Note: After reading the block, the file was named SW3515R_HW0828R_10254833AA. The first part is the software version, the second is the hardware version, and the third is the calibration number in Siemens format. Some loaders or calibrators may incorrectly interpret ECU identification data, resulting in file names like HW3515R_SW0010828R, where the software and hardware versions are swapped, and the “001” prefix (actually a supplier code from Siemens/VDO/Continental) is added to the software version. Despite this naming, the files themselves are correct.

EMS3132 – Working with calibrations:

“ VIN number: X7LLSRAAH8H1

Calibration: 8200915308

Main number: 8200661124

Hardware number: 8200598393

09:57:48 Module identification
09:57:50 Software Version: SW8200915308_HW8200598393
09:57:51 Access granted
09:57:51 Reading data
09:57:51 Reading block 1
09:58:46 Successfully completed

EMS3134, working with calibrations:

“ VIN number: X7L

Calibration: 8201142845

Main number: 8201051558

Hardware number: 8200933361

10:13:50 Module identification
10:13:50 Software Version: SW8201142845_HW8200933361
10:13:50 Access granted
10:13:51 Reading data
10:13:51 Reading block 1
10:14:42 Successfully completed

10:15:33 Module identification
10:15:34 Access granted
10:15:34 Erasing
10:15:35 Transferring data
10:15:35 Transferring block 1
10:16:16 Software validation
10:16:26 Completion
10:16:26 Successfully completed