BitEdit

Module for editing all diesel Bosch ECU's: EDC15, EDC16, EDC17 series for 1.4 and 1.6 D-4D Toyota engines.

We provide following maps for editing: Airmass maps for EGR, thresholds for EGR, desired boost maps and boost limitation, boost pressure vnt control maps, injection time control, fuel quantity maps, conversion from torque to fuel, quantity limitation maps, target lambda for smoke limitations, rail pressure maps, rail pressure limitation, start of injection maps, and also torque limitation, requested torque, gearbox torque maps, and torque monitoring maps and values (for EDC17).

Supported SW list

Software module allows editing and tuning Denso ECU 89661-xxxxx of diesel Toyota & Lexus cars with engines 2.0 and 2.2 litres

The folowing maps are available for editing: rail pressure, target fuel quantity, requested torque, torque limitation, boost pressure. For more efficient tuning also you can edit correction and limitation maps for main parameters, maps to control output circuits (injection quantity regulator, rail pressure regulaor) etc.

Cars supported:

Toyota Auris 2.0 D-4D
Toyota Avensis 2.0 D-4D
Toyota Avensis 2.2 D-4D
Toyota Corolla 2.2 D-4D
Toyota Rav4 2.0 D-4D
Toyota Rav4 2.2 D-4D
Toyota Verso 2.0 D-4D
Lexus IS220 D-4D
etc.

Engines supported:

1ADFTV
1CDFTV
2ADFTV
2ADFHV
etc.

Supported SW list for Module Toyota Denso Diesel 1

Software module allows editing and tuning Denso ECU 89661-xxxxx of diesel Toyota & Lexus cars with engines 2.5 and 3.5 litres.

The folowing maps are available for editing: rail pressure, target fuel quantity, requested torque, torque limitation, boost pressure. For more efficient tuning also you can edit correction and limitation maps for main parameters, maps to control output circuits (injection quantity regulator, rail pressure regulaor) etc.

Cars supported:

Toyota Dyna 3.0td
Toyota Fortuner 3.0td
Toyota HiAce 2.5td
Toyota HiLux 2.5td
Toyota HiLux 3.0td
Innova 2.5td
Toyota Land Cruiser 120 3.0td
Toyota Land Cruiser 150 Prado 3.0td
Toyota ToyoAce 3.0td
etc.

Engines supported:

1KDFTV
2KDFTV
etc.

Supported SW list for Module Toyota Denso Diesel 2

Software module allows editing and tuning Denso ECU 89661-xxxxx of diesel Toyota & Lexus cars with engines 4.5 litres

The folowing maps are available for editing:

Air control: Airmass corrections by fuel temperature, additive; Desired airmass for low load, Desired airmass; Minimal desired airmass.
Boost pressure: Desired boost pressure; Boost pressure basic map: correction and to limit boost when EGR is active; Boost pressure limiter correction factors; Boost pressure regulation basis; Coolant temperature factor for boost pressure correction, Desired and Final boost pressure limitation(relative), Desired boost pressure monitoring.
Boost pressure: VNT Control: Boost pressure regulator to predict deviation; VNT Control temperature and atmospheric pressure corrections; VNT Controls basis and corrections basis maps; Desired boost pressure limitation(relative), VNT Control maximal and minimal corrections; VNT Control minimal threshold.
EGR Control: EGR position corrections; EGR position limitations; Minimal and Maximal EGR positions requests; Target EGR position corrections; Target EGR Position.
Injection volume: Gear dependent injection volume limiter; Injection volume basis for minimal and maximal limitations; Injection volume corrections; Injection volume limitations; Minimal injection volumes.
Injection volume: conditional corrections.
Injection volume: smoke limitations.
Injector control: Injector opening time for main injection and Pilot injection time.
Limiters: Vehicle speed limitation.
Rail pressure: Rail pressure limitation, Rail pressure regulator basis, Target rail pressure.
Sensors scalings: Boost air temperature, Coolant temperature, Fuel temperature, Intake air temperature and MAF sensors scalings; Temperature correction for MAF sensor.
Start of injection calculation: Start of main and pilot injection.
Torque model: Drag loss torque correction, Fuel pump drag loss part from rail pressure, Fuel temperature drag loss part; Injection volume to Torque and Torque to injection volume conversions maps.
DTC mask

Cars supported:

Toyota Land Cruiser 200 4.5td
Toyota Land Cruiser 70 4.5td
Lexus LX450D

Engines supported:

1VDFTV

Supported SW list for Module Toyota Denso Diesel 3

Software module allows editing and tuning Denso ECU 89661-xxxxx (MCU 76F0040GD, 76F0039AGD, 76F0085) of turbo diesel Toyota Hino trucks with engines 4.0, 4.7, 4.9 litres.

The folowing maps are available for editing: rail pressure, target fuel quantity, requested torque, torque limitation, boost pressure. For more efficient tuning also you can edit correction and limitation maps for main parameters, maps to control output circuits (injection quantity regulator, rail pressure regulaor) etc.

Vehicles supported:

Toyota Hino Dutro 4.0td
Toyota Dyna 4.0td
Toyota Dyna 4.7td
Toyota Dyna 4.9td
Toyota ToyoAce 4.0td

Engines supported:

N04C
J05D
S05D

Supported SW list for Module Toyota Denso Diesel 4

Software module for editing calibrations Denso newGen ECU of diesel Toyota vehicles with engines 2.4 TD 2GDFTV and 2.8 TD 1GDFTV .

This module supports files:

• MCU D76F0196F1 1536Kb
• MCU D76F0219F1 2048Kb

The following maps are available for editing:

Air control and EGR - Desired airmass in additional mode, Airmass correction additive, Target EGR valve position in additional mode, EGR position correction, Maximum airmass flow
Boost pressure: desired value - Boost Pressure, Maximal allowed boost pressure(absolute), Boost Limiter
Boost pressure: VNT Control - Boost Pressure Actuator Duty Cycle, Boost pressure actuator base map, VNT Actuator
Driver request - Injection volume multiplier basis used for request calculation, Drivier request multiplier correction on acceleration, Injection volume multiplier from requested torque and engine speed
Injection - Main injection time, Pilot injection time
Injection volume - Injection volume correction factor via intake temperature, Injection volume correction factor via airmass flow, Maximal injection volume, Injection volume limitation in case of system error, Maximum Torque, Injection volume limitation
Input sensors - Intake air temperature sensor conversion curve, Boost air temperature sensor conversion curve, Coolant temperature sensor conversion curve
Limiter - Vehicle speed limitation
Rail pressure - Target rail pressure, Target rail pressure in regeneration mode, Rail pressure correction values, Maximal rail pressure, Rail pressure limiter, Rail Pressure
Start of injection - Start of main injection in additional mode, Start of pilot injection in additional mode
Torque model Requested torque, Accelerator pedal map
DTC mask

Vehicles supported:

Toyota HiLUX 2.4TD
Toyota HiLUX 2.8TD
Toyota LC150 2.8TD

Engines supported:

1GD-FTV
2GD-FTV

Supported SW list for Module Toyota Denso Diesel 5

Software module for editing calibrations Denso Gen3 ECUs of diesel Toyota vehicles

Supported engines: 2.4TD 2GDFTV, 2.8TD 1GDFTV, 3.3TD F33AFTV.

Supported filesize: 4Mb.

Available maps:

Air calculation: Air flow correction, Desired air calculation, Desired air calculation in additional mode
Boost Pressure: Base boost pressure in additional mode, Base boost pressure with active EGR
Boost Pressure Correction: Boost pressure correction from air temperature sensor, Boost pressure correction from atmospheric pressure, Boost pressure correction from coolant temperature
Boost Pressure Limitation: Boost limitation in emergency mode, Minimum boost pressure
EGR: Basic position of EGR, Correction of base position of EGR, Lower threshold of the moment for operation EGR, Upper threshold of the moment for operation EGR
Fuel pressure: Fuel pressure at start-up, Fuel pressure correction from coolant temperature, Fuel pressure in regeneration mode, Maximum fuel pressure, Maximum fuel pressure during regeneration
Initial injection phase: Initial injection phase in additional mode
Injection end phase: Main injection end phase when the post-injection is not active, Main injection end phase with active post-injection
Injection volume limitation: Base injection volume, Border of the transition from cold to warm operation mode, Border of the transition from warm to hot mode, Correction of maximum permissible injection volume, Injection volume limitation, Injection volume Limitation from air flow rate, Injection volume limitation from atmospheric pressure, Maximum injection volume from atmospheric pressure
Limiters: Engine speed limitation in additional mode, Minimum speed limitation in additional mode, Vehicle speed limitation (Test)
Nozzle performance: Nozzle performance at the 1st and 2nd pilot injection, Nozzle performance at the main injection
Pilot injection: Phase of the second pilot injection with active zero and first pilot injection, Pilot injection phase in additional mode, Second pilot injection phase with the first pilot injection active, The phase of the first pilot injection with the active second pilot injection, Zero pilot injection phase, Second pilot injection phase
Post injection: Post-injection phase
Post-injection volume: Basic post-injection volume
Sensors: Coolant temperature sensor, Intake air temperature sensor, Intake manifold air temperature sensor, Exhaust Temperature Sensor Scaling, SCR Temperature Sensor Scaling
Torque: Inversion requested torque, Requested torque
Torque loss: Base loss torque, Torque loss by coolant temperature, Loss torque on fuel pump by fuel pressure, Torque loss on fuel pump by fuel volume increasing
VNT: Base position of the VNT when the EGR is active, Base position of the VNT when the EGR is not active, Maximum VNT position when EGR is active, Maximum VNT position when EGR is inactive , Proportional coefficient for inactive EGR is the negative derivative, Proportional coefficient for inactive EGR is the positive derivative, Proportional coefficient with active EGR is the negative derivative, Proportional coefficient with active EGR is the positive derivative, Proportional gain for VGT duty cycle control
VNT correction: Additional correction to the base position of the VNT, Correction of the VNT base position
Volume of Pilot Injection: Volume of the 0-th pilot injection map, Volume of the 1st pilot injection, Volume of the 1st pilot injection with the active 0-th pilot injection map, Volume of the 2nd pilot injection with the 1st pilot injection active

DTC mask is not supported. Make sure that incorrect DTC modify can kill an ECU.

URGENT requests are not allowed in this module.

Supported SW list

Software module for editing calibrations Denso Gen3 ECUs of diesel Toyota vehicles

• Supported engines: 2.8TD 1GDFTV, 3.3TD F33AFTV
• Supported filesize: 4Mb
• Supported SW id: 8A222-xxxxx

Available maps:

Air calculation:

• Air flow correction
• Desired air calculation in additional mode

Boost Pressure:

• Base boost pressure
• Base boost pressure with active EGR, Minimum boost pressure

Boost Pressure Correction:

• Boost pressure correction from air temperature sensor
• Boost pressure correction from atmospheric pressure
• Boost pressure correction from coolant temperature

Boost Pressure Limitation:

• Boost limitation in emergency

EGR:

• Basic position of EGR
• Lower threshold of the moment for operation EGR
• Upper threshold of the moment for operation EGR

Fuel pressure:

• Fuel pressure at start-up
• Fuel pressure correction from coolant temperature
• Fuel pressure in regeneration mode
• Rail Pressure
• Maximum fuel pressure
• Maximum fuel pressure during regeneration

Initial injection phase:

• Initial injection phase

Injection volume limitation:

• Correction of maximum permissible injection volume
• Injection volume Limitation from air flow rate
• Injection volume limitation from atmospheric pressure
• Maximum injection volume from atmospheric pressure
• Base injection volume
• Injection volume limitation
• Border of the transition from cold to warm operation mode
• Border of the transition from warm to hot mode

Limiters:

• Engine Speed Limitation
• Minimum speed limitation, Vehicle Speed Limitation (Test)

Nozzle performance:

• Nozzle performance at the 1st and 2nd pilot injection
• Nozzle performance at the main injection

Post injection:

• Post-injection phase stage

Sensors:

• Coolant temperature sensor
• Exhaust Temperature Sensor Scaling
• Intake air temperature sensor
• Intake manifold air temperature sensor
• SCR Temperature Sensor Scaling

Torque:

• Inversion requested torque
• Requested torque

Torque loss:

• Torque loss on fuel pump by fuel pressure
• Torque loss on fuel pump by fuel volume increasing
• Base loss torque
• Torque loss by coolant temperature

VNT:

• Base position of the VNT
• Maximum VNT position
• Maximum VNT position when EGR is active
• Proportional gain for VGT duty cycle control
• Proportional coefficient for inactive EGR is the negative derivative
• Proportional coefficient for inactive EGR is the positive derivative

VNT correction:

• Additional correction to the base position of the VNT

Volume of Pilot Injection:

• Volume of the 0-th pilot injection
• Volume of the 1st pilot injection with the active 0-th pilot injection
• Volume of the 2nd pilot injection with the 1st pilot injection active
• Volume of the 3rd pilot injection with the 1st pilot injection active

DTC

Supported SW list for Module Toyota Denso Diesel 7

Software module for editing calibrations Denso ECU of petrol Toyota | Lexus | Scion vehicles with petrol normal aspirated engines 1.0, 1.2, 1.3, 1.6, 1.8 with ECUs Denso 89661-xxxxx and MCU NEC 76F0038, 76F0039, 76F0040, 76F0070, 76F0085 inside.

Fuel: enrichment Mass air flow sensor pulsations map, Enrichment for engine protection correction on retardation, Enrichment at full load, AFR value as stoichiometry, Delay for enable closed loop, Coolant temperature to enable closed loop, Enrichment for engine protection correction for full load, Throttle position threshold to enter full load, Throttle position threshold to exit from full load, Enrichment for engine protection base, Per cylinder enrichment multiplier
Input sensors: Accelerator pedal sensor 1, Accelerator pedal sensor 2, Correction for mass air flow via Intake temperature, Mass air flow sensor conversion curve
Limiters: Engine speed limitation, Vehicle speed limitation
Spark advance: Spark advance base, Spark advance low octane, Spark advance high octane, Minimal spark advance, Maximal spark advance
Throttle valve control: Throttle valve position limitation low load, Throttle valve position limitation full load
Exhaust temperature model: Calculated exhaust temperature 1, Calculated exhaust temperature 2, Calculated exhaust temperature 3, Calculated exhaust temperature 4, Calculated exhaust temperature 5, Exhaust temperature offset for spark retardation, Minimal exhaust temperature for engine protection, Maximal exhaust temperature for engine protection, Exhaust temperature offset for vehicle speed
Spark advance: knock: Engine speed lower threshold for retardation, Engine speed upper threshold for retardation, Retardation recovery rate, Spark advance retardation amount
Startup: Startup Time, Startup engine speed adder
Warm up: Coolant temperature threshold for cold engine, Warm up correction for P/N, Warm up correction for drive/reverse
Fuel: injector control: Injection time correction factor by load, Minimal injection time, Injector flow constant, Injector dead time, Minimal injection time when fault is stored
Spark advance: corrections: Spark advance base correction by coolant temperature, Spark advance base correction by coolant temperature 2, Spark advance corrections high/low octane, Spark advance correction for VVT, Spark advance correction for VVT high octane
Idle speed: Idle speed at P/N, Idle speed in drive position
VVT: Intake camshaft position, Exhaust camshaft position, Intake camshaft position at low throttle, Intake camshaft position at high throttle, INtake camshaft position at full load, Exhaust camshaft position at low throttle, Exhaust camshaft position at high throttle, Exhaust camshaft position at full load
Spark advance: minimal: Spark advance correction via coolant temperature, Minimal spark advance, Coolant temperature threshold for minimal spark advance correction
Torque model: Optimal torque 2, Optimal torque
DTC

Supported engines:

1KRFE
1NRFE
1NZFE
1NZFXE
1ZRFE

2NZFE
2SZFE
2ZRFE
2ZRFXE
3NRFE

Software module for editing calibrations Denso ECU of petrol Toyota | Lexus | Scion vehicles with petrol engines 2.0, 2.4, 2.5 and 2.7 litres with ECUs Denso 89661-xxxxx and MCU NEC 76F0038, 76F0039, 76F0040, 76F0070, 76F0085 inside.

For now we support following maps:

Air calculation: Calculated air load from requested torque, Mass air flow pulsations factor

Exhaust temperature model: Calculated exhaust temperature 1 in additional mode, Exhaust temperature offset for spark retardationExhaust temperature offset for vehicle speed, Maximal/Minimal exhaust temperature for engine protection

Fuel: enrichment: AFR value as stoichiometry, Coolant temperature to enable closed loop, Delay for enable closed loop, Enrichment for engine protection base, Enrichment for engine protection base, Enrichment for engine protection correction for full load, Enrichment for engine protection correction on retardation, Per cylinder enrichment multiplier, Throttle position threshold to enter full load, Throttle position threshold to exit from full load

Fuel: injector control: Injection time correction factor by load, Injector dead time, Minimal injection time, Minimal injection time when fault is stored, Minimal injection time when fault is stored

Limiters: Engine/Vehicle speed limitation

Sensors scaling: Intake air temperature correction factor for mass air flow, Mass air flow sensor scaling, Accelerator pedal sensor

Spark advance: Maximal/Minimal spark advance, Spark advance base, Spark advance high/low octane

Spark advance: corrections: Spark advance base correction by coolant temperature, Spark advance correction for VVT, Spark advance corrections high/low octane

Spark advance: knock: Coolant temperature threshold for retardation, Engine speed lower threshold for retardation, Engine speed lower threshold for retardation, Maximal spark advance retardation, Retardation recovery rate, Spark advance retardation amount

Spark advance: minimal: Coolant temperature threshold for minimal spark advance correction, Spark advance minimal base, Spark advance minimal temperature correction

Throttle valve control: Throttle valve maximal position, Throttle valve position limitation full load, Throttle valve position limitation low load, Accelerator pedal

Torque model: Optimal torque

VVT: Exhaust camshaft position base, Intake camshaft position at full load, Intake camshaft position at high throttle, Intake camshaft position at low throttle, Intake camshaft position base

DTC mask editor

Supported engines:

1ARFE
1AZFE
2ARFE
2AZFE
2TRFE
3ZRFE
3ZRFAE
4GRFSE
5GRFE etc

Supported SW list

Software module for editing calibrations Denso ECU of petrol Toyota | Lexus | Scion vehicles with engines 3.0, 3.3 and 3.5 litres with ECUs Denso 89661-xxxxx and MCU NEC 76F0038, 76F0039, 76F0040, 76F0070, 76F0085 inside.

Supported maps list:

Air calculation: Calculated air load from requested torque, Mass air flow pulsations factor
Automatic transmission downshift conditions: Output Speed vs Throttle in different mode
Automatic transmission: torque converter: Output Speed vs Throttle Normal in different mode apply, Output Speed vs Throttle Normal in different mode release, Torque converter in different mode apply, Torque converter in different mode release
Automatic transmission: torque converter flex: Output Speed vs Throttle Normal in different mode apply, Output Speed vs Throttle Normal in different mode release, Output Speed vs Throttle Sport in different mode apply, Output Speed vs Throttle Sport in different mode release, Toyota Temporary Curve
Automatic transmission: upshift conditions: Output Speed vs Throttle in different mode
Exhaust temperature model: Calculated exhaust temperature, Exhaust temperature offset for spark retardation , Exhaust temperature offset for vehicle speed, Maximal exhaust temperature for engine protection, Minimal exhaust temperature for engine protection
Fuel: enrichment: Injection time correction factor by load, Injector dead time, Minimal injection time, Minimal injection time when fault is stored
Idle speed: Desired idle speed at P/N, Desired idle speed in drive, Idle spark advance in gear, Idle spark advance P/N
Limiters: Engine speed limitation, Vehicle speed limitation
Sensor scaling: Intake air temperature correction factor for mass air flow, Mass air flow sensor scaling
Spark advance: Difference for idle spark advance from base, Minimal spark advance, Spark advance base, Spark advance delta for efficiency, Spark advance base efficiency, Spark advance base high/low octane, Spark advance base minimal temperature correction
Spark advance correction: Spark advance base correction by coolant temperature, Spark advance correction for VVT, Spark advance base correction high/low octane
Spark advance: knock: Coolant temperature threshold for minimal spark advance correction, Coolant temperature threshold for retardation, Engine speed lower (upper) threshold for retardation, Maximal spark advance retardation, Retardation recovery rate, Spark advance retardation amount, Total retardation limit
Spark advance: minimal: Coolant temperature threshold for minimal spark advance correction, Spark advance minimal base, Spark advance minimal temperature correction
Startup: Startup Time, Startup engine speed adder
Throttle valve: control Maximal throttle position on 1st gear, Maximal throttle position on reverse gear, Throttle valve maximal allowed position request, Throttle valve maximal position, Throttle valve position limitation at different gear, Throttle valve position limitation different load, Throttle valve position limitation on SAP fault
Throttle valve: request: Requested throttle position at different gear
Torque Converter – General: Coolant temperature to disable (enable) hot mode , Oil temperature to enable hot mode , Oil temperature threshold for high coolant temperature enable , Oil temperature threshold to disable hot mode, Oil temperature for high coolant disable
Torque model: Optimal torque, Optimal torque for transmission
VVT: Exhaust camshaft position at full load, Exhaust camshaft position at low throttle, Exhaust camshaft position at high throttle, Exhaust camshaft position base, Intake camshaft position at low throttle, Intake camshaft position at high throttle, Intake camshaft position at full load, Intake camshaft position base
Warm up: Coolant temperature threshold for cold engine, Warm up correction for drive/reverse, Warm up correction for P/N
DTC mask editor

Supported engines:

2JZGE
2GRFE
2GRFSE
3MZFE etc.

Supported SW list